DSMC2 V-Lock I/O Expander
DSMC2 V-Lock I/O Expander
описание DSMC2 V-Lock I/O Expander
С нашей камерой предостовляется бесплатно!
Аренда 1700 руб. будни / 1900 руб. выходные
Расширитель ввода-вывода DSMC2® V-Lock предлагает множество разъемов ввода / вывода, а также стандартное крепление V-Lock для питания вашей камеры DSMC2 с использованием батарей RED BRICK®. Этот модуль расширителя выполнен из легкого и прочного магния, который крепится непосредственно к задней части камеры и имеет следующие соединения:
• Вход постоянного тока (DC IN)
• Выход HDMI 1.2 (гнездо типа A)
• Выход 3G-SDI (HD-SDI, 75 Ом BNC)
• Порт CTRL и SYNC (2x 00B поддержка LEMO 4-Pin, Timecode и Genlock)
• AUX Выходная мощность (P-Tap 2-Pin female)
• Выходная мощность USB (тип A, 5 В при 1,5 А для питания передатчиков HDMI или небольших мобильных устройств)
• Стерео выход для наушников (гнездо 3,5 мм)
• Стерео аналоговый вход (гнездо 3,5 мм)
Расширитель ввода-вывода DSMC2 V-Lock также имеет селекторный переключатель, который позволяет камере автоматически загружаться, когда питание подается через разъем DC IN на расширителе. Эта функция позволяет использовать подключенный источник постоянного тока, чтобы включить и выключить камеру, когда она установлена в удаленных или труднодоступных местах.
-----------------------------------------------------------------------------------------
The DSMC2® V-Lock I/O Expander offers a variety of Input/Output connections, as well as an industry standard V-Lock mount to power your DSMC2 camera using RED BRICK® batteries. Constructed from lightweight and durable magnesium, this expander module mounts directly to the rear of the camera BRAIN® and offers connections for the following:
• DC Power input (DC IN)
• HDMI 1.2 output (Type A socket)
• 3G-SDI output (HD-SDI, 75 Ω BNC)
• CTRL & SYNC ports (2x 00B LEMO 4-Pin, Timecode and Genlock support)
• AUX Power output (P-Tap 2-Pin female)
• USB Power output (Type A, 5 V at 1.5 A for powering HDMI transmitters or small mobile devices)
• Stereo Headphone output (3.5 mm jack)
• Stereo Analog input (3.5 mm jack)
The DSMC2 V-Lock I/O Expander also features a selector switch that enables the BRAIN to automatically boot when power is provided via the DC IN connector on the expander. This feature allows you to use a connected DC input supply to turn the BRAIN on and off when the camera is mounted in remote or difficult to maneuver locations.
This expander is an ideal solution for a wide variety of production environments—from low-profile run-and-gun situations to studio shoots that require mobility.
NOTE: The DSMC2 Top Handle is NOT fully compatible with the DSMC2 Base I/O V-Lock Expander, as the top handle will interfere with the battery when one is attached to the expander module.
DIMENSIONS | Height: 4.57 in. (116.0 mm)
Width: 4.94 in. (125.5 mm) Depth: 2.25 in. (57.2 mm) (connected to BRAIN) |
WEIGHT | 1.0 lb (454 g) |
MATERIAL | Magnesium |
BRAIN MOUNTING | 4x M4 captive mounting screws |
BRAIN CONNECTIONS | Power delivery via Rear pogo connector (13-Pin)
Communication via Rear I/O connector (4×40 Pin) |
CONNECTORS | DC IN (6-Pin 1B LEMO socket)
3G-SDI output (75 Ω BNC), 60 Hz max frame rate HDMI 1.2 output (Type A socket), 60 Hz max frame rate SYNC (Genlock IN / Timecode IN / Sync IN) (4-Pin 00B LEMO socket) CTRL (Tally OUT / RS-232 Rx and Tx) (4-Pin 00B LEMO socket) USB Power output (Type A socket), 1.5A P-Tap Aux Power output (2-Pin), 3.0A Stereo Analog Microphone input (3.5mm jack) Stereo Headphone output (3.5mm jack) |
AUTO BOOT ON POWER | 2-position slider switch |
BATTERY COMPATIBILITY | RED BRICK |
AUDIO | 24-bit, 48 KHz, uncompressed, unbalanced mic level |
OPERATING TEMPERATURE | 0°C to 40°C (32°F to 104°F) |
STORAGE TEMPERATURE | –20°C to 50°C (–4°F to 122°F) |
OPERATING HUMIDITY | 0% to 85%, non-condensing |
STORAGE HUMIDITY | 0% to 85%, non-condensing |
FIRMWARE REQUIREMENT | Compatible with all DSMC2 firmware v6.2.17 or later. |